Full auto small bottle extrusion blow moulding machine

1. Festo cylinder 2. MITSUBISHI PLC 3. 4000 BPH 4. 200-2000L PET, PC, PV, PP bottle 5. full automatic

the standard operation of GP-Y2L-4000 extrusion blow molding machine includes four steps as follow Step 1. Put the preform into preform container and the conveyer will take the preform to orientation units automatically. Step 2. Load the preform at neck up to preform holder, and then preform is conveyed into baking tunnel. Step 3. After heating, preform is conveyed into the blow station, then close the mold, stretch and blow under low pressure and high pressure, exhaust, open the mold. Step 4. The finished bottle is taken off by automatic discharging system Features: A. Stable performance with advanced PLC. B. Conveying preforms automatically with conveyor. C. Strong penetrability and good and swift distribution of the heat by letting the bottles rotate by itself and revolute in the rails simultaneously in the infrared preheater. D. High adjustability to enable the preheater to preheat preforms in shapes by adjusting the light tube and the length of the reflecting board in the preheating area, and eternal temperature in the preheater with an automatic thermostatic apparatus. E. High safeties with security automatic-locking apparatus in each mechanical action, which will make the procedures turn into a state of safety in case of a breakdown in certain procedure. F. No contamination and low noise with the air cylinder to drive the action instead of the oil pump. G. Satisfaction with different atmospheric pressure for blowing and mechanical action by dividing the blowing and action into three parts in the air pressure diagram of the machine. H. Strong clamping force with high pressure and double crank links to lock the mold. I. Two ways of operating: Automatic and manual. J. Safe, reliable, and unique design of the position of valve to make the air pressure diagram of the machine easier to understand. K. Low cost, high efficiency, easy operation, easy maintenance, etc, with automatic technological process. L. Contamination is avoided for the bottle body. M. Ideal effect of the chilling with the chilling system. N. Easy installation and starting O. Low rejection rate: Less than 0.3percent.

TYPE	ITEM	UNIT	Technical data
Container	Product material	/	PET
	Container volume	L	0.05-2.0
	Theoretic output	Psc/hr	0.05-2L(2cavity)3300-4000
	Preform length	MM	50-200
	Max height of bottle	MM	320
Molding	Preform inner diameter	mm	15-60
	Bottle diameter	mm	35-110
	Max mold plate dimension (L × W)	mm	380 × 460
	Max mold thickness	mm	200
Air compressor	High pressure compressor	M3/Mpa	1.2/30 × 3set
	Locking force	KN	170
	Mold opening stroke (adjustable)	mm	200
	Low pressure compressor	M3/Mpa	2.0/30 × 1sets
	Air dryer	M3/Mpa	2.0/30 × 1sets
Main machine electricity	Power	KW	30
	Voltage / frequency	V/Hz	380/50hz
Machine size and weight	Main machine (L × W × H)	M	4.3 × 1.8 × 2.0
	Main machine weight	T	4
	Conveyor (L × W × H)	M	1.4 × 1.1 × 1.85
	Conveyor weight	T	0.4
	High pressure compressor (L × W × H)	M	1.90 × 0.75 × 1.50 × 1sets
	Low pressure compressor (L × W × H)	M	1.85 × 0.75 × 1.50
	High pressure air reservoir tank (D × H)	M	0.70 × 2.25/3.0
	Air dryer (L × W × H)	M	0.85 × 0.50 × 0.95
	Air filters	Kg	10 × 5pc
Cooling water: cooling water recycling system can be used with its power of 8~10 liter per minute and 2~3 kilos water pressure
Total power: 51.9 KW high pressure air volume (1m/min); low pressure air volume (1.2m/min)
Safety	Auto emergency alarm	Safety inter-locking device

 

Full auto small bottle extrusion blow moulding machine